Displaying 1 - 24 of 935
X2 - Wand Err Codes Here is a list of the error codes and ways to troubleshoot them: X2 - Controller code CODE description SOLUTION FAIL The provisioning failed Re-provision the device donE The previous operation is complete N/A bAd/SSID/OR/PASS/CodE​ The …
ST-1700V - Installation Guide FLANGE DETAIL Discharge port (OPEN) Discharge port (AUTO) Solenoid Water line to filter Water line to valve-in-head INSTALLATION DETAIL Solenoid wiring 2" (50 mm) BSP Concrete or soil Water line (Optional) isolation valve … …
ST-1700V - Performance Chart Nozzle Pressure Radius Flow Precip mm/hr   bar kPa m m³/hr l/min 16 • Black 4.0 400 32.0 21.0 350 41.0 47.3 5.0 500 35.0 22.7 379 37.1 42.8 6.0 600 37.0 25.9 432 37.8 43.7 7.0 700 38.5 28.1 469 38.0 43.9 8.0 800 40.0 30.4 508 …
I-50 Correct Installation Correct Installation I-50 adjustable arc rotors should be installed flush at ground level (see Fig. 1). …
I-50 Arc Adjustments Adjustments (not for “ON” opposing-nozzle models) All I-50 adjustable arc rotors are preset to approximately 180°. Sprinklers can be adjusted with water on or off.  Use your hand to rotate the nozzle turret counterclockwise to the …
I-50 Radius Adjustment Insert the hex end of the Hunter wrench into the nozzle-retainer/ range-adjustment screw (see Fig. 3). Turn the screw clockwise into the stream of water to decrease the radius, or counterclockwise to increase the …
I-50 Precipitation Rate Adjustment Where excessively wet or dry areas are a problem, the precipitation rate may be adjusted. Simply replace the existing nozzle with a larger one to increase or a smaller one to decrease the rate of precipitation. … Where …
I-50 Nozzle Installation 1 Insert the key end of the Hunter wrench into the lift-up socket of a pop-up sprinkler. Pull the riser up to gain access to the nozzle socket. 2 Using the Hunter wrench, loosen the nozzle-retainer/ range-adjustment screw. If a …
ST-1700V - Accessing the valve-in-head Remove the rotor (see Replacing the cover and rotor ). Remove the boot. Unscrew the six Allen bolts on the piston flange. Remove the piston. 1 Remove the snap ring with the snap ring removal tool. 2 Remove the valve …
How do I manually open a zone control valve without using the controller? Simply twist the solenoid on the valve counter clockwise 1/4 turn to 1/2 a turn. To shut off the valve, twist the solenoid clockwise until it is snug on the valve.   … Simply twist …
NODE-BT - Controller Settings CONTROLLER SETTINGS offers more advance features. Rain Sensor Clik-Delay Soil Moisture Sensor Naming Programs and Stations Cycle & Soak Programmable Days Off Seasonal Adjustment Delay Between Stations Pump/Master Valve Set …
My Hunter SRC controller reverts back to the current time when I try to run a station, what is wrong with my controller? Over the life span of an SRC controller, surges and electrical strikes can wear on the internal components of the SRC’s circuit …
Replacement Guide: I-35 Rotors Receive Hunter quality and Hunter performance with the right substitute for your non-Hunter sprinklers. I-35 Rotor Replacement Chart   I-35 Gear Driven Rotary Sprinklers To Replace Use Hunter Nozzle toro 2001 9 (Red) 9 (Lt. …
Replacement Guide: PGJ Rotors Replacement Guide: Spray Sprinklers and PGJ Rotary Sprinklers Receive Hunter quality and Hunter performance with the right substitute for your non-Hunter sprinklers. PGJ Replacement Guide   PGJ Gear Driven Rotary Sprinklers …
Replacement Guide: PGP Ultra / I-20 Rotors Receive Hunter quality and Hunter performance with the right substitute for your non-Hunter sprinklers   PGP ULTRA / I-20 Rotor Replacement Chart   PGP Ultra/I-20 Gear Driven Rotary Sprinklers To Replace Use …
Replacement Guide: PGP-ADJ Rotor Receive Hunter quality and Hunter performance with the right substitute for your non-Hunter sprinklers. PGP-ADJ Rotor Replacement Chart PGP® Gear Driven Rotary Sprinklers To Replace Use Hunter Nozzle Rain Bird®       red …
Mini-Weather Station Installation Instructions The three sensors combined on this product are for wind speed, rainfall and temperature (near-freezing conditions). Each sensor operates independently of the other; therefore, any or all of them may be …
What should I check if the controller has a partial or blank display? A controller with a partial or blank display usually has damage to an electronic component on the internal circuit board. Normally this type of damage cannot be repaired. If the …
Where can I purchase replacement keys for my Hunter controller? Key sets for Hunter controllers can be purchased at a Hunter Authorized Distributor in your area. You can also purchase a key set through the Ewing Online Store . Find a Hunter Distributor …
How long should the non-volatile memory last on my Hunter controller? Non-volatile memory is a feature on all Hunter controllers, back up memory is stored with the assistance of a lithium battery installed inside the controller. This lithium battery is …
How many stations can I run at one time using the Pro-C's programming? The Pro-C controller will allow for only a single program to run at a time. Therefore you will have to be sure no two programs overlap. In the Set Station Run Times position the Total …
How long does it take for a Hunter rain sensor to dry out? The dry out time could be as little as 4 hours depending on the weather conditions (temperature and humidity) and the rain threshold that is set. If the weather conditions remain cold and damp, …
Eco-Logic - System Off Eco Logic: System Off System Off To turn your controller off, press the Mode button until the arrow is pointing at the System Off . Wait 2 seconds and the display will read OFF. Valves currently watering will be shut off. All active …
Accu Sync Overview Accu Sync ® is a pressure regulation device designed by Hunter to fit all Hunter valves. Accu Sync installs quickly and easily beneath the solenoid on top of your Hunter valve. Check out the video below for an overview of Accu Sync's …