Displaying 337 - 360 of 398
Hunter Dual Two-Wire Installation: Tee-Splicing the Two-Wire Path 7 of 8
Video 7 of 8 installation of the Hunter Dual decoder two-wire system with I-Core controller. Tee-Splicing the two-wire path.
Hunter Dual Two-Wire Installation: Connecting Decoders to Valve Solenoids 5 of 8
Video 5 of 8 to installation of the Hunter Dual decoder two-wire system with I-Core controller. Connecting decoders to valve solenoids.
Hunter Dual Two-Wire Installation: Connecting DUAL-S Surge Suppressors 6 of 8
Video 6 of 8 of installation of the Hunter Dual decoder two-wire system with I-Core controller. Connecting DUAL-S surge suppressors in line and at the
Hunter Dual Two-Wire Installation: Dual Connecting Two-Wire Paths 4 of 8
Video 4 of 8 installation of the Hunter Dual decoder two-wire system with I-Core controller. This section will go over connecting 2-Wire paths.
Hunter Dual Two-Wire Installation: Dual Grounding 2 of 8
Video 2 of 8 installation of the Hunter Dual decoder two-wire system with I-Core controller. Grounding the Controller is a vital step in the two wire
Hunter Dual Two-Wire Installation: Installing the Dual 48M Decoder Output Module 3 of 8
Video 3 of 4 installation of the Hunter Dual decoder two-wire system with I-Core controller. In this section we will instal the Dual 48M decoder output
Hunter Dual Two-Wire Installation: Introduction 1 of 8
Introduction to installation of the Hunter Dual decoder two-wire system with I-Core controller. This video series will go over DUAL, a two-wire decoder
Solar Sync - Programming - Part 1 of 2: Controller Setup
Solar Sync is a sensor system that, when connected to a Hunter controller, will automatically adjust your controller watering based upon changes in
Solar Sync - Programming - Part 2 of 2: Programming the Solar Sync Module
Solar Sync is a sensor system that, when connected to a Hunter controller, will automatically adjust your controller watering based upon changes in
MP Rotator Series: How to Adjust Hunter's MP Rotator
Adjusting the arc and radius of an MP Rotator is an easy task. There are two adjustments, arc and radius, that can be made on an MP Rotator. Arc: The
ACC Advanced Programming: Solar Sync Setup
This video will show you how to properly set up and install a Solar Sync weather sensor with the ACC commercial irrigation controller.
Where is this box going?? An inside peak at Hunter's shipping facility
At Hunter we try our hardest to get each order delivered as quickly as possible to our distribution partners. This video shows a box of PGPs getting
Rain Sensors - FAQs
If your controller is showing a message indicating that the sensor is active even thought it has not rained or if the sensor is not shutting down the
Wireless Rain Clik - FAQs
If your wireless sensor is not shutting down irrigation when it rains or if the Sensor Status LED on the receiver continues to be red after the sensor
Troubleshooting a Hunter Valve that is not Opening - Quick Tip
One of the most common reasons for a valve not to open when the controller sends low voltage electricity to the valve is because the exhaust port might
Cleaning the Diaphragm on a Hunter Valve - Quick Tip
One of the most common reasons for a valve to keep running continuously is the accumulation of debris in the diaphragm, which prevents the valve from
Roam Remote Control Programming
This video provides an overview on how to set up and operate your Roam remote control including how to turn on and off stations as well as changing
Canceling Extra Start Times on Hunter Controller
An irrigation system that is repeating the cycle and continuously watering most likely has too many start times programmed into the controller. This
Programming Odd & Even Days and Programming Interval Watering
This video will teach you how to program your controller to water every other day by selecting odd or even days of the week to water. You will also
Canceling a Delay on a Hunter Controller
One of the most common reasons for a sprinkler system to water intermittently and show the word DELAY on the display is because a delay time was
How to Reset a Hunter Controller
If want to clear the memory on your controller and start from fresh or if your controller is not responding to your commands, this video will show you
Controllers - Programming Multiple Programs Part 1 of 4: Introduction, Time/Date
Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It
Controllers - Programming Multiple Programs Part 2 of 4: Program A
Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It
Controllers - Programming Multiple Programs Part 3 of 4: Program B
Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It