Displaying 361 - 384 of 411
Where is this box going?? An inside peak at Hunter's shipping facility
At Hunter we try our hardest to get each order delivered as quickly as possible to our distribution partners. This video shows a box of PGPs getting
Rain Sensors - FAQs
If your controller is showing a message indicating that the sensor is active even thought it has not rained or if the sensor is not shutting down the
Wireless Rain Clik - FAQs
If your wireless sensor is not shutting down irrigation when it rains or if the Sensor Status LED on the receiver continues to be red after the sensor
Troubleshooting a Hunter Valve that is not Opening - Quick Tip
One of the most common reasons for a valve not to open when the controller sends low voltage electricity to the valve is because the exhaust port might
Cleaning the Diaphragm on a Hunter Valve - Quick Tip
One of the most common reasons for a valve to keep running continuously is the accumulation of debris in the diaphragm, which prevents the valve from
Roam Remote Control Programming
This video provides an overview on how to set up and operate your Roam remote control including how to turn on and off stations as well as changing
Canceling Extra Start Times on Hunter Controller
An irrigation system that is repeating the cycle and continuously watering most likely has too many start times programmed into the controller. This
Programming Odd & Even Days and Programming Interval Watering
This video will teach you how to program your controller to water every other day by selecting odd or even days of the week to water. You will also
Canceling a Delay on a Hunter Controller
One of the most common reasons for a sprinkler system to water intermittently and show the word DELAY on the display is because a delay time was
How to Reset a Hunter Controller
If want to clear the memory on your controller and start from fresh or if your controller is not responding to your commands, this video will show you
Controllers - Programming Multiple Programs Part 1 of 4: Introduction, Time/Date
Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It
Controllers - Programming Multiple Programs Part 2 of 4: Program A
Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It
Controllers - Programming Multiple Programs Part 3 of 4: Program B
Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It
Controllers - Programming Multiple Programs Part 4 of 4: Other Modes
Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It
Display Troubleshooting on a Hunter Controller
If your display is blank, unreadable, or if it is showing symbols that do not make any sense, this video will teach you how to troubleshoot the display.
Manual Operation with a Hunter Controller
Hunter controllers allow you to start a station or an entire program manually. To do so, turn the dial to Manual Single Station or Manual All Stations
Cleaning a Filter on a Hunter Rotor
The most common reason for a sprinkler to stop rotating is the accumulation of debris in the filter. This video will teach you how to clean the filter
I-Core Controller: Basic Start-up Programming
Irrigation professional Mike Madewell will walk you through programing the Hunter I-Core controller. In part one basic start-up programming, Mike will
I-Core Controller: Advanced Programming with Extended Features
In part two advanced programming and extended features, Mike will go through seasonal adjust, cycle and soak, delay between stations and configuration
I-Core Controller: Solar Sync Setup
This video teaches you how to connect, configure, and program a solar sync weather sensor with your I-Core controller. Installation of both the wired
I-Core Controller HFS Flow Sensor Set-up
In part three of the Hunter Flow-Sync Sensor setup, Mike will go through installing the sensor and setting up stations to be monitored, change overflow
Accu Sync Valve Pressure Regulator Installation, Adjustment and Overview
The Accu Sync pressure regulator is designed to regulate the pressure at the valve for the entire zone to provide maximum water efficiency. Learn how to
ICR Remote Control - Programming & Operation
This video provides an overview on how to set up and operate your ICR remote control including how to turn on and off stations as well as changing their
ICR Remote Control - Setting the Address
If you can activate your stations from your controller, but you can't activate them from your remote control, it is possible that your transmitter is