Wired Rain-Clik™ - Installation Instructions

Share
Topics: 
Installation Procedures

Before wiring your Rain-Clik, it is important to select an appropriate mounting location for the transmitter. Click here to view mounting instructions for the Rain-Click transmitter.

Once the Rain-Clik is mounted, run the wire to the controller, and fasten it every few feet with wire clips or staples for best results. If an extension to the wire provided is needed, use the following table to determine the minimum wire gauge needed:

Rain-Clik Lead Wire Extension
Extension length Minimum wire gauge
25 to 50 ft. 20 AWG
50 to 100 ft. 18 AWG
100 to 200 ft. 16 AWG

Wiring to Your Irrigation System

X-Core Controller

The Rain-Clik connects directly to the X-Core or XC. This allows you to easily override the sensor by using the Sensor switch on the front panel.

  1. Remove the jumper from the two “SEN” terminals.
  2. Route the wires from the rain sensor up through the same conduit opening used for valve wiring.
  3. Connect one wire to the terminal labeled “SEN” and the other wire to the other “SEN” terminal.

Rain-Click Connecting to X-Core Controller

I-Core Controller

The Rain-Clik connects directly to the I-Core. This allows you to easily override the sensor by using the Sensor switch on the front panel.

  1. Remove the jumper from the two “SEN” terminals.
  2. Route the wires from the rain sensor up through the same conduit opening used for valve wiring.
  3. Connect one wire to the terminal labeled “SEN” and the other wire to the other “SEN” terminal.

Rain-Click Connecting to I-Core Controller

Pro-C Controller

The Rain-Clik connects directly to the Pro-C. This allows you to easily override the sensor by using the Sensor switch on the front panel.

  1. Remove the jumper from the two “SEN” terminals.
  2. Route the wires from the rain sensor up through the same conduit opening used for valve wiring.
  3. Connect one wire to the terminal labeled “SEN” and the other wire to the other “SEN” terminal.

Rain-Click Connecting to Pro-C Controller

ACC Controller

The Rain-Clik connects directly to the ACC. This allows you to easily override the sensor by using the Sensor switch on the front panel.

  1. Remove the jumper from the two “SEN” terminals.
  2. Route the wires from the rain sensor up through the same conduit opening used for valve wiring.
  3. Connect one wire to the terminal labeled “SEN” and the other wire to the other “SEN” terminal.

Other Hunter Controllers

 

Other Controllers - 24 Volt Solenoid Valves Only (No booster pump)

  1. With the two wires from the Rain-Clik at the controller, locate the “common ground” wire of the solenoid valves. If it is connected to the common terminal on the controller, disconnect it.
  2. Attach one wire of the Rain-Clik to the “common” terminal (usually marked “C”) on the controller.
  3. Attach the other wire of the Rain-Clik to the common wire leading to the valves.

Note: The common wire to the valves does not have to be interrupted at the controller. The Rain-Clik may be wired anywhere along the common wire line.

Other Controllers - 24 Volt Solenoid Valves with Booster Pump

  1. Locate the common wire to the solenoid valves and the common wire leading to the coil of the relay that starts the pump. If these two wires are connected to the “common” terminal on the controller, disconnect both of them.
  2. Twist together these two wires along with one wire from the Rain-Clik, and secure with a wire nut.
  3. Attach the other wire of the Rain-Clik to the “common” terminal on the controller.

Note: The pump circuit output must be 24 Volts in this situation. Do not proceed if 110V.

  1. Line-In
  2. Normall-Open Relay
  3. Line-Out (to Pump)
  4. Common Wire to All Valves
  5. Solenoid Valves

Hunter SRC (Discontinued)

The Rain-Clik connects directly to the SRC. This allows you to easily override the sensor by using the RUN (BYPASS SENSOR) position on the dial.

  1. Route the wires from the Rain-Clik up through the same opening used for valve wiring.
  2. Connect one wire to the RS terminal and other to the C terminal.
  3. Connect the valve common to the RS terminal.
Operation Check to Verify Correct Wiring
Turn on one zone of the irrigation system that is visible while you are in reach of the Rain-Clik. Use manual ALL STATIONS or OneTouch Start (right arrow) to start irrigation. Do not use manual single station as that will over-ride an active sensor. Manually depress the spindle at the top of the Rain-Clik until you hear the switch “click” off. The sprinkler zone should stop instantaneously. If it does not, check wiring for correctness. It is not necessary to “wet” test the Rain-Clik, although it will test the operation fine, if desired.

Resources

Rate this Article: 
Average: 3.5 (2 votes)

Related Links