X2 Support

The X2 controller has a non-replaceable 3V CR2032 lithium battery installed directly on the circuit board. The controller will immediately enter hibernation mode when AC power is

Before securing the controller to the wall, you must first remove the lower wiring compartment door. The door can easily be removed by following the simple steps below: Open

Included in the box are mounting screws and anchors.

Valve Wire Sizing (Maximum One-Way Distance in Feet Between Controller and Valve)Ground Wire SizeControl Wire (mm²)Below is a chart indicating the maximum wire runs that can be

NOTE: Complete this section only if you have a master valve installed in your irrigation system. A master valve is a “normally closed” valve installed at the supply point of the

NOTE: Complete this section only if you have a pump start relay installed. A pump start relay is a device that uses a signal from the controller to actuate a separate electrical

A Hunter CLIK sensor or closed circuit type weather sensors can be connected to the X2. The purpose of this sensor is to stop automatic watering when weather conditions dictate.

The X2 Controller is compatible with Hunter Remote Controls (not included). The SmartPort® wiring harness (included with all Hunter Remotes) allows for fast and easy use of the

NOTE: In the Start Times dial position, the numbers 1-4 do not represent stations. The numbers represent the program start times. Each program can start up to 4 times on the set

Seasonal Adjust is used to make global run time changes without re-programming the entire controller. This feature is perfect for making small changes that are necessary as the

The X2 allows the user a simplified method for running a test program. This feature operates each station in numerical sequence, from the lowest to the highest. You can start with

Hunter X2 controller has a rain sensor bypass switch located on the left hand side of the facepack. To bypass (turn off) the sensor using the switch on the controller, follow

You can also activate all stations to water without using the dial.

The X2 controller will not water manually or automatically with the dial in the system off position. Valves currently watering will be shut off after the dial is turned to the

This feature permits the user to stop all programmed waterings for a designated period from 1 to 99 days. At the end of the programmed rain off period, the controller will resume

The X2 allows the user to program the controller so that the sensor disables watering on only desired stations. For example, patio gardens that have pots under overhangs and roofs

The Cycle and Soak feature allows you to split a station’s runtime into shorter watering periods. The shorter watering periods will help prevent run off in situations like slopes

This feature allows the user to select a time delay between the end of one station run time and the start of another station's run time. The delay can be set for 1 second up to 8

The X2 is factory configured with 3 independent programs (A, B, C with four start times each) for different plant type requirements. The X2 can be customized to display only the

The CLIK DELAY option is designed to set number of days for watering to remain off, after sensor has been activated and restored.

The X2 keeps a running total of each program's station run times. This feature provides a quick way to determine how long each program will water.

The Easy Retrieve feature allows the user to save a program in the controller's memory for later use. The saved program can be retrieved at any time to overwrite unwanted changes

If you simply want to start over or if your controller is not responding to your commands, you can reset the X2 controller easily.  This will return the controller back to factory

This circuit diagnostic procedure is can quickly identify shorts; commonly caused by faulty solenoids or when a bare common wire touches a bare station control wire. ​ To

  Wi-Fi setup button WAND serial number Wi-Fi status LED

Once installed, a solid amber Sorry, your browser does not support inline SVG. LED will appear on the module near the right of the dial positions and the  icon will appear on

NOTE: The serial number is used to activate the WAND on Hydrawise. You will be prompted to enter the serial in the online setup process when adding the controller to your

  Enable the Wi-Fi setting on your device. Press the WAND button twice: The solid amber LED on module will blink twice per second and “SAP” will appear on the controller

Press the WAND button three times: The solid amber  LED on the module will blink three times per second and 'Pbc' will appear on the controller LCD. Press

  Press and hold the WAND button for 5 seconds and 'Fdr' will appear on the controller LCD. The module LED will turn off. Release the button when the solid amber Sorry,

Solid LED Color: ● WAND is waiting for user to add Wi-Fi credentials. ● Controller is Online and connected to Hydrawise server. ● Incorrect Wi-Fi password entered or Wi-Fi