Solar Sync Support

Welcome to the Solar Sync sensor support section. The Solar Sync sensor comes in wired and wireless versions and will automatically adjust the controller run time based on the sensors reading of the weather. In this section you will find information on how to install, adjust, wire and troubleshoot the Hunter Solar Sync sensor

  • Introduction
    The.Solar Sync is a sensor system that, when connected to a compatible Hunter controller, will automatically adjust your controller watering run times based upon changes in local
  • Sensor Overview
    The Solar Sync sensor is simple and easy to install and is compatible with all current Hunter AC powered controllers. The sensor should be  placed in an area where it can receive
  • Installing the Sensor
  • Connecting to X-Core
    The X-Core Controller is programmed with Solar Sync technology and, therefore, does not require the use of the Solar Sync module. Installing the Wireless Solar Sync Sensor
  • Connecting to Pro-C
    The Pro-C / PCC controller (with SOLAR SYNC position on dial) is programmed with the Solar Sync technology and, therefore, does not require the use of the Solar Sync module. The
  • Connecting to I-Core
    The I-Core now has the Solar Sync software built into the controller. New I-Core controllers with built in Solar Sync are easily identified by the new Solar Sync Settings dial
  • Connecting to ICC2
    The ICC2 controller is programmed with Solar Sync technology and, therefore, does not require the use of the Solar Sync module.The Solar Sync Sensor (SOLARSYNCSEN or WSSSEN) is
  • Connecting to ACC
    The ACC Controller is programmed with Solar Sync technology and, therefore, does not require the use of the Solar Sync module. Installing the Wireless Solar Sync Sensor
  • Connecting to Other Hunter Controllers
    Connecting to the ICCThe Hunter ICC controllers require the installation of the Solar Sync module as well as the Sensor.Installing the Solar Sync ModuleTurn off AC power to the
  • Connecting to Multiple Controllers
    Solar Sync ET sensor can share one sensor transmitter with multiple Hunter AC controllers. To accomplish this setup, each controller would need a separate wireless Solar Sync
  • Clik Operation
  • Bypassing the Sensor
    If the Rain Sensor or Freeze Sensor is preventing system operation, SENSOR OFF will be displayed on the controller’s display. Simply move the Bypass switch on the controller to
  • Maintaining the Sensor
      Maintaining the sensor The Solar Sync sensor is designed for outdoor use, but must be kept clean to function correctly. Wiping the clear dome covering the solar
  • Making Adjustments
    After Solar Sync has been installed and programmed, we recommend allowing the system to run for a few days at the initial setting. Because of the variety in site conditions
  • Module Programming
    For controllers with the Solar Sync Module installed, the Region and Water Adjustment is made on the Solar Sync Module.
  • Region and Water Adjustment
    For accurate Solar Sync measurements, the controller needs to be programmed for the average peak season ET for your region. Use the following table for choosing your region. You
  • Station Run Times
    It is important to understand that Solar Sync provides a global seasonal adjustment to the controller. This means that all station run times will be modified by the seasonal
  • Addressing WSS
    The Wireless Solar Sync Receiver and Sensor are already paired with the same frequency for an easy installation. When installed, the wireless Receiver will automatically go into a
  • Seasonal Adjustment Incorrect
    If the Solar Sync Seasonal Adjustment is too high or too low you may need to change the Water Adjustment feature on your controller or Solar Sync Module on older models. This will
  • ERR Message
  • Stations Wet or Dry
    One station:At any time you can simply increase or decrease Run Time to any individual station in the host controller and that station will adjust up and down with all the rest of
  • Battery Information
    The battery in the Wireless Solar Sync® Transmitter is designed to operate for the life of the sensor by providing a sealed, maintenance-free design. The transmitter is available
  • Warranty
    Hunter warrants all Solar Sync models for five years. If a defect in a Hunter product is discovered during the applicable warranty period, Hunter will repair or replace, at its

Find Hunter