A2C-LTE - Antenna Installation

Metal Controllers

Metal controllers will include a hole plug assembly in a pre-drilled factory hole on top of the controller. Remove the nut on the inside of the controller to remove the plug. Route the cable through the pre-drilled hole and the antenna nut. Then tighten the nut on the antenna securely. Apply RTV sealant around the hole, filling the gap between the enclosure hole and the mounting threads. Route the antenna cable through the track on the back of the door frame to the module in the facepack. Leave just enough slack to allow the door to open and close without pinching the cable. Connect the cable to the module and tighten by hand.

Plastic controllers
  1. Carefully drill a ½" (13 mm) hole in the top of the plastic wall mount, where indicated by the printed circle on top of the controller.
  2. Remove all plastic debris left behind after drilling. Remove the nut from the antenna assembly.
  3. Route the antenna cable through the hole and the nut. Apply RTV sealant around the hole, filling the gap between the enclosure hole and the mounting threads. Tighten the nut securely.
  4. Route the antenna cable through the track on the back of the doorframe to the module in the facepack. Leave just enough slack to allow the door to open and close without pinching the cable. Connect the cable to the module and tighten it by hand. 
  5. Route the antenna cable through the hole in the bracket. Install the antenna on the bracket with the nut. Tighten the nut securely.
  6. Route the cable from the bracket through the conduit down, over, and into the controller enclosure via the conduit holes in the bottom of the enclosure.
  7. Route the antenna cable through the track on the back of the doorframe to the module in the facepack. Leave just enough slack to allow the door to open and close without pinching the cable. Connect the cable to the module and tighten it by hand.

 

 

Existing metal enclosures

The antenna must be installed outside the controller enclosure on a metal bracket. Do not drill the enclosure directly. These installations require a Hunter wall bracket (P/N - WALLANTBRKT) to complete the installation. The antenna includes approximately 9' (2.8 m) of cable.

  1. Use the lower switch on the bottom of the transformer to turn off power to the controller.
  2. Fasten the mounting bracket to the wall with the supplied hardware.
  3. Route the antenna cable down through the hole in the bracket, the washer, and the lock nut.
  4. Use the supplied alcohol wipes to clean the top of the bracket. Allow the area to dry.
  5. Peel the sticker off the bottom of the disk antenna. Then apply the antenna firmly to the mount.
  6. Use ½" (13 mm) or ¾" (20 mm) conduit fittings to route the antenna cable to the controller. If necessary, use the supplied 4' (120 cm) extension cable.
  7. Attach the conduit to the ½" (13 mm) conduit hole in the bottom of the controller with fittings.
  8. Route the antenna cable into the controller. Then attach the communication module antenna connector. Hand-tighten only.
  9. Turn on the power and test the unit.

Plastic pedestal

Plastic pedestal mounting requires a lid adapter (P/N -PEDLIDANTBRKT).

  1. Route the antenna cable through the hole in the bracket. Secure the antenna to the mounting bracket with the supplied nut.
  2. Use the included screws to install the bracket so the antenna protrudes into the recess in the pedestal lid, as shown.
  3. Install the plastic cable guides as shown to secure the antenna cable and prevent it from pinching the cable when the lid is closed.
  4. Route the cable down the hole to the side of the facepack frame. Connect it to the connector on the LTE module. Do not allow any metal portion of the antenna cable to touch metal or earth ground with the power on.
  5. Turn on the controller power. After the controller reboots, the networking icon should appear on the bottom of the Home screen.

 

Still need help? We're here.

Tell us what you need support with and we'll find the best solution for you.

Contact Support